Laguna Woods Repiping

To repipe or repair, that is the question...

Laguna Woods repiping

Re-water-piping (repipe) normally involves replacing the entire interior hot and cold water distribution system. This includes all of the main lines and branch lines throughout the home or building, right up to each plumbing fixture.

A quality repipe job will include the main cut-off valve, individual fixture cut-offs (stops) and supply tubes. TIP: This is also a good opportunity to replace any old valves or faucets since they will need to be disconnected anyway.

Depending on the situation and composition, the outside water main feeding your home may also need replacing during the process.

Avoiding disaster

One thing is certain when doing such an extensive job, and that is to use a licensed, bonded and insured plumbing contractor who specializes in repiping. Check credentials, get 3 bids and note the following...

  • Proper permits and inspections must occur for your protection and compliance.
  • All repiping must meet code for proper materials, sizing and workmanship.
  • Oftentimes portions of walls or ceilings will need be opened to accommodate plumbing, so know up front who is responsible for closing and repairing, and to what extent.
  • Know up front what kind of piping materials will be used.
  • Know up front exactly how piping will be routed and secured and if any will be exposed.
  • Understand exactly to what extent water piping will be replaced (some contractors could take shortcuts to undercut bids and not go “all the way”, such as including fixture supplies, stops, dishwasher feeds, etc.). Make sure you’re getting your money’s worth so you won’t be fixing more leaks in the future!

Obtain detailed, written proposals to avoid any misunderstanding and make sure everything above is covered. Compare apples to apples - the lowest bid may not be your best value in the long run. Be sure to include a proposal from Laguna Woods, the repiping specialists and learn firsthand why we are different and how you will benefit.

A professionally repiped home will add value and peace of mind for many years to come. A “cheap” job can end up being a nightmare. Getting it done right the first time avoids hassles, headaches, mess and is more cost effective in the long run.

How will I know if I need to repipe my home or business?

Here are some signs to watch for...

Poor water pressure or volume:

  • Does your water just trickle out of your faucets?
  • Do you get scalded in the shower whenever someone else flushes a toilet?
  • When running the water, does the volume noticeably drop when someone else does the same?
  • Does it seem to take way too long to fill up a sink, tub or toilet?

Contact us for a free evaluation and estimate. This could be caused by old, galvanized steel water piping which is rusting closed inside causing a major flow-restriction. This would be similar to a “hardening of the arteries” restricting blood flow.

Does your water come out red and rusty looking, especially at first blast?

Review the above. This is likely the same galvanized piping which is rusting away. Be aware of other side effects:

  • Rust particles and minerals can also plug up and restrict your plumbing valves, faucets, dishwashers, washing machines, shower heads and toilets.
  • They can also cause staining of fixtures and finishes.
  • These particles and minerals are also unhealthy for your body, especially when drinking.

Another reason for repiping is leaking or corroded pipes.

Sometimes this can be visible when piping is exposed such as around water heaters, under framed houses or in basements. However, in the vast majority of cases pipes are hidden under concrete slabs, buried underground and hidden in walls. In most cases, homeowners are not aware of pipe condition until they experience a leak.

For more information on this, see our informative pages on Slab Leak Repairs and Leak Detection.

In addition to the galvanized piping above, copper tubing is also prone to leaking. This typically develops as a pinhole leak that grows bigger until noticed as a leak when above ground, or discovered by hearing or a high water bill if underground.

During an initial leak, speak with the plumber to learn the cause and condition of your pipes. Was there a particular reason for the leak, or does it appear that your pipes are just old and rotting away?

Some homeowners will go ahead and repipe to avoid further damage to their home and costly repairs. Others will wait until they’ve had another leak or two before finally throwing in the towel.

Our recommendation is that if it appears to be inevitable, you should do it sooner than later. In this manner the money that would be spent on repairs and subsequent damage could be diverted to a permanent cure for the problem. Also, the price of labor and materials will only continue to rise with inflation. You will have more time to plan and shop around when not in an emergency situation.

Types of water piping

Galvanized steel:
We’ve touched on this already. It’s primarily found in older hopes and was used prior to copper taking over, beginning in the 1950’s and 60’s. This is where the plumber used their monkey wrenches instead of soldering torches because galvanized steel pipe and fitting are all threaded (sometimes referred to as screw pipe). The cutting and threading of the longer pipe runs was a very arduous task requiring a good amount of skill and the proper tools and machinery.

Although rarely used for inside water piping today, there are still some old water mains feeding homes outside. If your water pressure is low in your home even though your pipes are copper or plastic, it could be that you have one of these old water mains.

Copper tubing:
Copper has been prevalent for the last several decades. Originally thought to last the life of the structure, we have found out otherwise over time. A lot depends on the corrosive minerals and acidity of the water and the rest primarily on the wall-thickness of the tubing.

Copper comes in 3 wall-thicknesses, the thickest being type K copper. Due to its high cost and difficulty in cutting and soldering, it is very rarely used in homes. It’s typically used for special circumstances requiring more durability in commercial and industrial applications.

Type L copper is very popular, being the “mid-wall” thickness and found in a lot of homes. Finally is type M copper which was also used a lot for water piping. This is the thinnest of the 3 grades, being almost as thin-walled as an eggshell.

Since copper is expensive, plumbers typically use whatever grade copper is permitted by code; in some parts of the country that would be type L and in others it would be type M. As one can imagine, if the water supply source in a particular area is highly corrosive, the thin-wall type M copper may only last a few years. In other parts of the country with good quality water, the exact same copper tubing could last as long as the structure...

PVC pipe:
Poly Vinyl Chloride is a popular type of white plastic pipe which is primarily used outside for water mains and irrigation. It is very durable, non-corrosive and inexpensive and uses special primer and glue (cement) to fuse the pipe and fittings together. It’s also popular for swimming pool plumbing since it’s impervious to chlorine corrosion.

The proper thickness must be used for domestic water use (schedule 40). Thinner-walled PVC may be used for certain irrigation lines where not under high pressure. It should not be used where exposed to the sun’s ultra violet rays. It is for cold water use only - never to be used for hot water or for any water piping inside a home or building. (Schedule 40 PVC Drainage piping is also used in homes and buildings.)

CPVC pipe:
This is another type of plastic pipe which is specially formulated to also handle hot water lines, although it is not allowed where exposed to sunlight. It is not as thick-walled as PVC, comparing more to the outside diameter of copper tubing and is yellowish-almond in color. It also uses its own specially formulated cement and primer to fuse pipes and fittings together. Since it’s relatively inexpensive and can carry hot water as well as cold, it can be used for water piping a home in certain parts of the country, but not very often. This is due to its rigidity, thin walls and brittle nature. This means more fittings are required to get around where it needs to go and more labor to assemble. It also means being extra careful around the pipes during and after installation to avoid breakage. For obvious reasons, it is used more by do-it-yourselfers than plumbers and again, is not permitted in many jurisdictions.

Pex pipe (www.pexinfo.com):
PEX (or crosslinked polyethylene) has several advantages over metal pipe (copper, iron, lead) or rigid plastic pipe (PVC, CPVC, ABS) systems. It’s flexible, resistant to scale and chlorine, doesn't corrode or develop pinholes, is faster to install than metal or rigid plastic, and has fewer connections and fittings to impede flow.

Pex has become the piping of choice for plumbers in recent years for a variety of reasons:

  • Flexibilty - Pex is super flexible and hard to kink. This means it’s great for repipe jobs since it can be “fished around” through difficult areas thus reducing fittings, labor and lateral damage.
  • Fewer joints - Naturally, fewer joints equates to less flow restrictions, less possibility for leaks and reduced installation costs.
  • No glue, primer or cement - Plumbers and homeowners alike enjoy the “odor-free” installations. The solvents used with other types of materials can be very dangerous to inhale and work with, especially in confined, poorly ventilated areas. This also eliminates solvents from getting inside the pipes and water system. Instead, Pex uses heavy-duty insert fittings and special crimping rings for assembly. A specially calibrated tool, or crimper, is used to make up the joints.
  • Superior material - Pex is safe, corrosion resistant, thick walled and resilient. No more rust, pinholes or leaks. It out-performs other materials in assembly, durability and longevity. To learn more visit www.pexinfo.com.

For questions, expert advice, free consultation and the area’s best repiping company, contact Laguna Woods Plumbing today!

Zip Codes for Laguna Woods, California:

92637, 92654

Schedule an
Appointment

Seniors Discount visa

Call us to speak with someone immediately!
(951) 787-0777

24 Hour Emergency
Plumbing Service Calls

You will discover hardly any other plumbing & drain professional within the greater Laguna Woods neighborhood better set up to manage your current unexpected emergency as well as urgent needs. Disregarding the time of day or night, you will always speak with a live home comfort professional on the phone. And we are committed in our effort to respond to each and every repair required within one hour.

Plumbing Services
Laguna Woods, California

  • Laguna Woods Backflow Prevention
  • Laguna Woods Basement Waterproofing
  • Laguna Woods Bathroom Remodeling
  • Laguna Woods Ceiling Leaks
  • Laguna Woods Circulation Pumps
  • Laguna Woods Clogged Drains
  • Laguna Woods Copper Plumbing Piping
  • Laguna Woods Drain Cleaning
  • Laguna Woods Leaking Faucets Leaking
  • Laguna Woods Garbage Disposals
  • Laguna Woods Hydro Jetting Service
  • Laguna Woods Leak Detection
  • Laguna Woods Low Flow Toilets
  • Laguna Woods Pipe Freezing
  • Laguna Woods Pipe Location Service
  • Laguna Woods Pressure Relief Valves
  • Laguna Woods Pumps
  • Laguna Woods Roof Drains
  • Laguna Woods Sewer Back-ups
  • Laguna Woods Shower Heads
  • Laguna Woods Shower Pans
  • Laguna Woods Leaking Sink
  • Laguna Woods Sump Pumps
  • Laguna Woods Tank less Hot Water Heaters
  • Laguna Woods Leaking Toilets
  • Laguna Woods Plumbing Trench less
  • Laguna Woods Leaking bathtubs
  • Laguna Woods Urinals
  • Laguna Woods Plumbing Video Inspection
  • Laguna Woods Water Heaters
  • Laguna Woods Water Pressure Issues
  • Laguna Woods Yard Drains
  • Laguna Woods Rooter
  • Laguna Woods Flood and Water Damage